Amsoil Break In SAE 30 Engine Oil 946ml

£12.74 inc. VAT

Break your engine in with peace of mind

4 in stock

“AMSOIL Break-In Oil is an SAE 30 viscosity grade oil formulated without friction modifiers to allow for quick and efficient piston ring seating in new and rebuilt high-performance and racing engines. It contains zinc and phosphorus anti-wear additives to protect cam lobes, lifters and rockers during the critical break-in period when wear rates are highest, while its increased film strength protects rod and main bearings from damage. AMSOIL Break-In Oil is designed to increase compression, horsepower and torque for maximum engine performance.

Quickly Seats Rings

The primary goal during engine break-in is to seat the rings against the cylinder wall. Properly seated rings increase compression, resulting in maximum horsepower; they reduce oil consumption and prevent hot combustion gases from entering the crankcase. To achieve this, however, the oil must allow the correct level of ?controlled wear? to occur between the cylinder wall/ring interface while maintaining wear protection on other critical engine parts. Insufficient break-in leaves behind peaks on the cylinder wall that prevent the rings from seating. The deeper valleys, meanwhile, allow excess oil to collect and burn during combustion, increasing oil consumption. Too much wear results in cylinder glazing due to peaks ?rolling over? into the valleys and preventing oil from collecting and adequately lubricating the cylinder wall.

AMSOIL Break-In Oil?s friction-modifier-free formula allows the sharp peaks on newly honed cylinder walls (fig. 1) to partially flatten. The result produces more surface area for rings to seat against, allowing formation of a dynamic seal that increases compression, horsepower and torque (fig. 2).

cylinders

Protects Critical Parts from Wear

New flat-tappet camshafts and lifters are not seasoned or broken in and must be heat-cycled to achieve proper hardness. During the break-in period, these components are susceptible to accelerated wear because they are splash-lubricated, unlike other areas of the engine that are pressure lubricated. AMSOIL Break-In Oil contains high levels of zinc and phosphorus (ZDDP) additives designed to provide the anti-wear protection required during this critical period.

Increased Film Strength

High-performance and racing engines often use aftermarket parts designed to increase torque and horsepower. The added stress can rupture the oil film responsible for preventing harmful metal-to-metal contact on rod and main bearings. The base oils in AMSOIL Break-In Oil provide increased film strength to protect bearings from wear.

APPLICATIONS

AMSOIL Break-In Oil is designed to effectively break in high-performance and racing engines requiring SAE 30 oil, helping maximize compression, horsepower and torque.

RECOMMENDATIONS

The engine builder?s or manufacturer?s break-in recommendations should be followed if available. Break-in period should not exceed 1,000 miles. When the engine is new, the exhaust ports will have a large area of oil residue (Fig. 3). As the rings begin to seat, less oil is passed and the oil residue area begins to shrink (Fig. 4). When the rings are fully seated and have formed a tight seal against the cylinder walls, no oil residue will be evident. Other common methods to determine if rings have seated include performing a leak-down test or horsepower measurements over time. Break-in duration will vary between engines. Afterwards, drain and fill the engine with an AMSOIL high-performance synthetic oil that meets builder or manufacturer specifications.

residue

HEALTH & SAFETY

This product is not expected to cause health concerns when used for the intended application and according to the recommendations in the Material Safety Data Sheet (MSDS). An MSDS is available via the Internet at www.amsoil.com or upon request at (715) 392-7101. Keep Out of Reach of Children. Don?t pollute. Return used oil to collection centers.

For warranty information, visit www.amsoil.com/warranty.aspx.”

Additional information

Shipping Weight 0.91 kg
Shipping Dimensions 9.5 × 8 × 22 cm
Brand

Amsoil

Viscosity

SAE 30

Size

946ml

Model

Mk1 (89-98), Mk2 (98-05), Mk3 (05-15), Mk4 (15-24)

Warranty information

Warranties cover defects in materials and workmanship only. Warranty is for replacement of a similar product, repair of the original product or refund of the purchase value only and excludes all labour and incurred charges including towing, fitting, inconvenience, and purchases of other manufacturer's products. The warranty is good for the period stated in the additional info tab from the date of purchase. Mileage warranties are for road use only and proof of mileage is required. Products must be installed by an independent experienced professional mechanic and the suspected defect must be present at the outset. The warranty does not cover damage caused by incorrect installation, failure to comply with the maintenance requirements of the vehicle, processing or otherwise changing the product, ordinary wear and tear, or any other external influences. Warranties are invalid if the product is used for racing, rallying, drifting, track days or any other form of motorsport or competition. Please refer to the manufacturer's own warranty documentation for more information.

Making a warranty claim

Proof of purchase receipt showing the date of purchase, proof of mileage at installation, proof of current mileage and invoice of the work undertaken by an independent experienced professional mechanic must be supplied along with the returned products for a warranty claim to be considered. If your vehicle needs to be used whilst your warranty claim is considered replacement parts from the same manufacturer should be purchased through BOFI Racing. In the event of a successful warranty claim, we will refund the card that was originally used to purchase the replacement parts, in full or in part depending on the nature of the claim. BOFI Racing reserves the right to make full or partial compensation at its sole discretion depending on the condition and mileage use of the returned suspect parts. For example, if you have used the part for several thousand miles before a defect is noticed, only partial compensation may be offered.